I have a 1988 ford mustang with the 2.3l. I am having trouble trying to figure out a lowering technique I can use for my car. All the lowering kits I have seen...
The lowering kits for the V-8 and V-6 should work fine for your car. I would stick with the V-6, though, since the V-8 is a much heavier engine, and its kit...
Just curious if I kept it street legal. What would be the approx. max horsepower I could get out of it. Completely open to some suggestions. I do not want to...
HEY EVERYBODY IVE GOT AN N/A 88' MUSTANG 2.3L AND I HAVE JUST RECENTLY PULLED THE COMPUTER, INJECTORS, AND TURBO MANIFOLD FROM A TURBO XR-7 AND WAS WONDERING...
Ryan, The wiring is quite different, the stock 88 is speed density and the turbos are all vane air metered systems. best thing to do is to is to use the wiring...
Hi everybody, I just thought I would mention the white gauge faces that I sell for Mustangs. If anyone is interested, e-me privately / off list or use my web...
Hey ive got an '88 2.3L mustang. So far i have cold air induction, a 2 1/4 single catback exhaust, and my timing bumped ten degrees. I hoping to achieve 130 -...
I raced these engines for several years, and found that they couldn't take that much timing. I'd take at least half that out, and try other things. With a good...
the turbo 2.3's are mostly a drop in! (use the turbo engine wiring and eec though) a modded 23 turbo can deliver as much as 300hp maybe more if your rich LOL! ...
Whats wrong with having ten more degrees of timing? also where could I find a "street/strip" camshaft that will work with my fuel injection?? ... couldn't ... ...
You engine is designed to produce maximum bmep (pressure inside the combustion chamber above the piston) shortly after top dead center(tdc). This is the most...
I'm looking to give my car at least 225hp. I'm aware of a 2.3L turbo swap, but can a turbo be added to a 2.3L n/a by switching exhaust manifolds and so forth....
You can add the turbo the the n/a engine BUT... it will probably last about 5 minuted as the boost will most likely blow the pistons apart. the n/a engines do...
Hi, Looking for center caps for turbine 15" rims. I currently have an '87 LX w/2.3L and swapping out the 14" rims for the larger ones. If anyone should happen...
OK - Probably a very broad question. I have tons of experience with a 5.0 Mustangs but am considering getting into rally racing (Group 2) that limits engine...
The 2.3 is a very tough engine, super strong bottm end. There are TONS of aftermarket ho up parts avaialable for it (racer walsh in jax, FL is a good start) if...
I am thinking about bring my milling my head so i can get a 10:5:1 compression ratio. How much would i need to mill off? Also what kind of a power increase...
Ryan, Power increase will depends greatly on the reat of your engine and its mods. how is yoru engine setup at the moment? ... MCA Member 54006 Webmaster, The...
Shaving the head will help, i would port and polish the intake at the same time though. I would also look into a better cam, on EFI cars with TFI module, use...
Hey, i've found the best 4 cyl stang site. It is esslinger racing .com and the carry headers, heads, cams, stroker kits, and alot of other kool stuff. They...
I saw a nitrous 2.3L Pinto run 10.40s at Maple Grove Dragway in PA in summer of 2001. But it was all race car. I forget how big a shot it was but at 10.40...
I'm thinking about installing a set of Cobra R 17x9's with 245/45zr- 17 tires on my car I was wondering if anyone had done this before, if so did they have to...
... if ... lowered ... on? Well it is done I had to gut my front fender wells. I also had to buy 1/4 inch spacers for the front, because it was rubbing on my...
We would like to remind you of this upcoming event. Annual Pismo Beach Car Show Date: Monday, June 16, 2003 Time: All Day Annual Pismo Beach Car Show (Jun...
4and6cylindermustangs...
Jun 2, 2003 12:02 am
176
Hey Everybody, I was just wondering if anybody knows where I could find the throttle body adapter for a stock 94' to 95' 5.0 throttle body on a 2.3 engine. I...
Hey all, my mustang is going in june.12 for a new exhaust (2.25" / catback / flowmaster 40 series) and a custom intake (k&n filter / metal piping / rubber tube...
