I saw a nitrous 2.3L Pinto run 10.40s at Maple Grove Dragway in PA in summer of 2001. But it was all race car. I forget how big a shot it was but at 10.40...
I'm thinking about installing a set of Cobra R 17x9's with 245/45zr- 17 tires on my car I was wondering if anyone had done this before, if so did they have to...
... if ... lowered ... on? Well it is done I had to gut my front fender wells. I also had to buy 1/4 inch spacers for the front, because it was rubbing on my...
We would like to remind you of this upcoming event. Annual Pismo Beach Car Show Date: Monday, June 16, 2003 Time: All Day Annual Pismo Beach Car Show (Jun...
4and6cylindermustangs...
Jun 2, 2003 12:02 am
176
Hey Everybody, I was just wondering if anybody knows where I could find the throttle body adapter for a stock 94' to 95' 5.0 throttle body on a 2.3 engine. I...
Hey all, my mustang is going in june.12 for a new exhaust (2.25" / catback / flowmaster 40 series) and a custom intake (k&n filter / metal piping / rubber tube...
my 2.3L stang is losing lots of power don't have the slightest clue why. THe problem starts when I accelarate, .. it doesn't, well it does but very, very slow...
We would like to remind you of this upcoming event. Annual Pismo Beach Car Show Date: Monday, June 16, 2003 Time: All Day Annual Pismo Beach Car Show (Jun...
4and6cylindermustangs...
Jun 14, 2003 12:02 am
180
Hola! I have an '87 with a problem -- the bottom half of the ignition switch is broken. This is the section of the switch that, via an eleven-pin connector,...
the 8 plug head was the cam in the ranger 2.3 the same as the mustang 2.3? Also how much would you have to have the head shaved to rase the compression up...
... my ... this ... turbo had a higher nickel content in it that is why you have almost no wear in the cylenders from normal running also the con rods are like...
Hi All, I am new member of this group. We have a Mustang Convertible 1999 in Turkey. The problem is: When i start the engine of my car and put the gear D or R...
Could be a bad ignition switch, use your fist and thump under the steering column and see if that affects things. You might be able to take it out and tighten...
I just uploaded a photo of my new 86 SVO and put a link up for our club here on the coast of CA http://autos.groups.yahoo.com/group/4and6cylindermustangs/...
I'm new to this so I may have alot of questions... such as.... :) can anybody tell me if an 84 v6 automatic will bolt into an 89 4cyl w/a 5 spd manual tranny?...
both are mustangs the 84 is a hatchback and the 89 is a notchback. I want to bsicaly know if my v6 will bolt to the 89 and its 5 spd tranny. There are 2...
I'll have to ask my son, he's a Ford mechanic here in Orlando. He has a '95 hatch and a '95 Cobra. I have a '98 but it's only a 3.8 six. There might be a...
That was supposed to say '93 hatch...duh. ... From: JOHN GROENENDAAL To: 4and6cylindermustangs@yahoogroups.com Sent: Friday, August 08, 2003 6:47 PM Subject:...
Justin. Son Dave isn't sure but we don't think the 4-cyl. bellhousing or flywheel will fit onto the V6. Hope you tried the Fordnatics forum. Why not a V8...
thanks for the tips, I will keep my eyes open in the boneyard, if i get my carb fixed, as for goin 5.0 i do have a nice fairly fresh 302 out of an 80 ltd that...
Motorcraft, says my son who is a Senior Master Tech at Tropical Ford in Orlando, FL. He drives a 2.3 too, in a '93 Mustang. ... From: pbierhuizen To:...
Hello all, I have a 1990 2.3L Mustang LX which I am looking to upgrade, but there are a few questions I have at this point. First of all, how difficult is it...
