Rex/Dave/all: It is (and always has been) OK to talk about non-Digitrax products used in a Digitrax environment. The Team Digital products certainly fall into...
Hi Folks: Phil Perry has written a detailed description of how to install a decoder in the Life-Like N Scale Proto 2-8-4 Berkshire. This description is now ...
Frank, I had the same problem Thursday with this decoder. Once I reset all of the CV'S to factory default, it worked fine. I had read in the file section that...
It kept giving error message that a .dll could not be found. I tried to load it but several attemps failed. I blew the download away and tried it again, but...
Any of the Digitrax xx3 decoders should do for most HO open frame motors. A caution, though: some of the earlier Tenshodo motors had very high operating...
Can a global cammand be sent by a Command Station or Boster so that all Loco's are at Half throttle? With a DB150 a Global Stop can be sent, and I use that to...
I was programing a DS54 and now my DCS200 will not work in run mode. The only thing connected is a test track. The disply will not come on at all in run mode...
Ed, A little more detail will be required before we can begin to assist; which operating system are you using, which DLL is reported as missing. Before...
Don, What throttle are you using? Is the throttle giving the correct indication for track power? It is possible that you've got the track power on in "stop ...
Group - In the Big Book for DCC by Digitrax it states in the Norcross Southern section that a separate booster is suggested to operate turnouts and signals....
mdwebber
mdwebber@...
Jan 1, 2005 6:10 pm
80089
... I run one district for DS54's. Actually its the first run off My DCS and the reset of the layout is protected by Tony's Power Shields. That way a short on...
... reset ... Just a side thought. Add a DPDT sw so you change change the Buss to the Programming Track. That way you don't have to remove the DS54 to ...
The throttle is a DT400. It is blank in run mode and will not start when I hit power and Y/+ to start track power. Display is still blank. Thanks, Don ... ...
I'm sorry. I must disagree with your wire sizes. We use #12 gauge stranded wire in parallel with the rails with drop wires of 18 to 20 gauge. Using smaller...
... turnouts and signals. But is this separate bus also divided into power districts like the common rail bus?< This separate bus could be the one output of a...
Digitrax List Monthly Reminder! Links to the Digitrax List Archives: Messages at; http://groups.yahoo.com/group/digitrax/messages/ Files at; ...
digitrax@yahoogroups....
Jan 1, 2005 6:34 pm
80095
Digitrax List Monthly Reminder! Instructions for Unsubscribing from the Digitrax List: UPDATED: 06/03/2000 for eGroups 01/28/2001 for YaHoo! 04/28/2002 for...
digitrax@yahoogroups....
Jan 1, 2005 6:34 pm
80096
The buss they are talking about is the loconet. This is what connects your command station to your throttles through the UP's. they also want this cable to...
I would recommend using # 12 for the main busses, even on small layouts. The cost difference is very small, # 12 is available in numerous colors, and stranded...
Hi to all that replied to my idea of having a separate group for discussing T.D. problems & solutions used in conjunction with Digitrax products. I now see...
I was not requesting assistance, Tom asked me the question. Unfortunately I'm 600 miles from home were my L/O and computers are so its hard to do anything ...
The "blank screen" on the throttle makes me think it is not powered. Do you have a battery in the throttle? If not, try inserting a battery, and then see if...
I am in the process of hooking up the Program "DecoderPro " on my Computer I have installed the Program on the Computer OK, but find the Info on Interfacing...
Unfortunately the DT400 display works in program mode. Also Railroad & Co. software will not run my trains ether. Thanks, Don ... From: "Ross Kudlick"...
One cable from the computer to the Locobufffer II, then a loconet cable to the Chief. the program track is connected to the Chief. You need a locobuffer II....
I wouldn't be afraid to remoter the engine, especially with a decent can motor. They are easy to install, simply use calking compound to set the motor in...
Don, I'm assuming that the "Mode" switch on the DCS200 is in the "run" position. I don't think you can program if it is in any other position. At this point,...
I have to comment on the "new" site. It's excellent and a vast change from what was before. Everything on my older system works fine, no overlapping words,...
Please change my Email address to farosenbaum1@... I will not have any other Email account. The Gratiot Valley Railroad Club bi-annual train show and...
