Sometimes the simple answer helps. Have you made sure that the program track and the wheels are clean? The currents on the PT are quite small, and dirt will...
Not funny! :>( ... From: "The Boomsmas" <bboomsma@...> To: <Digitrax@yahoogroups.com> Sent: Tuesday, February 28, 2006 11:17 PM Subject: [Digitrax] New...
That was because I when I Downloaded ver 5.5 it was setup with a lenz system as the default system. I removed the Lenz system and now I have C & T. Now back to...
Hi Mitch, Had the same problem with a Bachmann Loco. A 1k resistor accross the programing track solved the problem. Dianna Lee ... Hi Mitch, Has it *ever*...
... of us that ... Off or ... Digitrax ... Off ... Off ... Off T ... C Off ... they use a ... By that ... off make ... Of course. I should have been able to...
Thanks Mick, Nope, the tain isnt dirty...I tried programming it right out of the box. And I had a feeling that the track might have been an issue so I ...
The simplest way would be to visit your local Radio Shack (if it has not shut down yet) and get a 1K ohm resistor and a pair of small aligator clips. Solder...
List, I am trying to match my various N scale locos speed etc CV's. However in the booklet supplied with the decoder it states thet a full list of CV's are...
Yes, The video and article in Model Railroader magazine are MR's annual April fools day jokes. Last year IIRC it was a new modular system called "NoTrack", in...
You're probably looking at the instruction sheet for your specific decoder. You want the Digitrax Mobile Decoder Manual which covers all Digitrax decoders. Go...
I am using Peco Code 80 manual turnouts on a 20' X 38' N scale layout. My operating scheme replicates ABS territory with permission to occupy main track given...
I have never used a flashing green, However I think it would be eazier and better to wire everything uniformily and then program using this panel to ...
Mike, Down load this manual, it should be a little more helpful http://www.digitrax.com/ftp/decodermanual.pdf Model Railroading with DCC is fun, Rich S. ... ...
What a great imagination, or have you been puffing the "magic smoke" ofter produced by us newbies making miscalculations in installing DCC? The video won't be...
Thanks for the info. I've wondered why from time to time I've had to change things. I think I will stay with one flashing color and wire the whole thing the...
John, I got the video to play.....guess my sense of humor is not here today as I did not find it particularly funny. Sorry! Phil ... From: "John Bisset"...
Actually the led is operable up to 18 vdc. I have tested it on a regular power pack and it lights fine. I have installed dropping resistors in the 400 ohm to...
The whole video is very funny. Too bad you got up on the wrong side of the bed. Fred In a message dated 3/1/2006 10:27:14 A.M. Eastern Standard Time, ...
Has anyone tried to use the IOMAX1 IOVI MAXIMIZER from MPLX ELECTRONICS SYSTEMS P.O. BOX 1732 HENDERSON, TEXAS 75653 as a booster? It is briefly listed under...
Group, I remember seeing some posts relating to this subject some time ago, but cannot find the proper heading for them. Anyway, setting up at shows and...
Hi guys and girls, I am trying to hook up a DS52 Stationary decoder to my Digitrax and it doesnt work. Can anyone help me with it? I bought the Empire Builder...
Some older Lenz decoders do not support reading back CV data. My solution is to program them "blind." In a suitable progamming mode, press "CV" then key in...
Be sure that the configuration jumper is closed and the programming jumper is open. Also, be sure that the DB150 is not in programming mode (very little power...
Hi Doug, I have the configuration jumper closed (for Tortoises), and the programming open (no programming). The DB150 is not programming, I am running the...
My F unit Stewart with DH163 was performing normally last week. Monday I put it on the track and could not call up the loco. Tried all kinds of stuff,...
