Hi Guys, If anyone could offer any help/advice/suggestions with a proble i'm facing I'd be grateful. The problem is that when I playback MIDI through my...
paper___cup@...
May 3, 2001 10:05 pm
49
Hi, Just got myself an Orbit V2 second hand and just wanted to know if anyone had any suggestions for getting decent jungle/drum and bass basslines out of the...
Julian Diggle
jdiggle@...
May 17, 2001 8:48 am
50
Try this: In Cakewalk Options->Project->MidiOut check Transmit Midi Start/Continue/Stop Clock and set the Midi output port to the right port for your Orbit....
John Bair
jbair@...
May 19, 2001 1:55 am
51
Also, to restore presets to factory setting, hold down the < and > cursor buttons while powering on the Orbit which activates the diagnostics menu. Then cursor...
John Bair
jbair@...
May 19, 2001 2:03 am
52
Hi can anyone help..... I'm looking for the V2 ROM, does anyone have one...? thanks den...
Den Jones
djones@...
May 21, 2001 1:48 pm
53
Hi den, I upgraded my V1 for a V2, but this is made through a ROM swapping (I mean physically). I could probably dump the ROM to get a copy on the PC, but you...
Amaury
amaurylb@...
May 22, 2001 6:57 am
54
Hi, Thanks for your mail, but I'm trying to find a chip.... but everyone's sold out..... any ideas..... thanks in advance den...
Den Jones
djones@...
May 22, 2001 10:17 am
55
I found the one I use in the UK. The store name was Turnkey, but I think they've changed their name. You can try http://www.turnkey.co.uk or ...
Amaury
amaurylb@...
May 22, 2001 11:55 am
56
... i totally lucked out when i found mine - it was on the clearance table at a Guitar Center for $75... good luck!...
Chuck Hunt
ckhunt@...
May 22, 2001 4:37 pm
57
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the EMU-Orbit_and_V2 group. File :...
EMU-Orbit_and_V2@yaho...
May 22, 2001 4:50 pm
58
Guys, The Orbit Manual has a complete listing of the instruments/sounds in Orbit at the back. My question is how do these sounds correspond to the banks? ie,...
paper___cup@...
Jun 7, 2001 10:26 pm
59
Each one of the presets in the 5 banks is made up using a combination of these sounds listed at the back of the manual. To find out which sounds are used in a...
Julian Diggle
jdiggle@...
Jun 8, 2001 8:35 am
60
Hello again everyone... & everyone at Drummachine.com, So, I'm an electronic musician [serious hobbyist] and I'm building a new studio from the ground up. I'd...
Erik Wiese
erikwiese@...
Jun 24, 2001 12:36 pm
61
Hi to all, Am new here and was wondering if there is anyone out there who's using the Orbit V2 withe the Phat-boy V2 controller? If so, I could do with some...
John
hainesmusic@...
Jun 24, 2001 11:59 pm
62
My name is Rex Henry. I am a drum and bass producer. I have my own label called Mystic Records. I live in Italy. I have a Orbit among other synths and I am ...
REX HENRY
djrextacy@...
Jul 13, 2001 9:39 am
63
Hi to anyone still out there... a couple of questions: 1) is anybody using any patch utils for Orbit? The only two I know of are OrbEdit and MidiQuest? I had a...
1) SoundDiver from Emagic supports the various Orbits. It uses their Proteus module, which will address any of the E-Mu Proteus-based ROMplers. Works like a...
Maybe a stupid question, but in beats mode, how do you change the beat number(not prg\bank- change) of the 100 presets from a secuencer (cubase) in a song? I...
Hi, I'm new, trying to find some info on the Orbit vs. the Orbit Version 2. Can someone please highlight the differences between the two? Is the version two...
Hi Friends, I Have modified some patches from the Ram Banks in my Orbit V2 and I would like to know if anyone has the originals factory presets in sysex file...
What about the "factory defaults reset" ? (I can't remember the key sequence though. Check your manual.) Wouldn't that clear everything back to the original...
Marvin, Are you sure that there is a key sequence where I can reset all my orbit, cause I have checked all the manual and I didn't find it. Thanks Marcelo ...
... Hold down the two cursor keys while powering up the unit. Turn the encoder to get to the 'Initialize' choice. Then press the Enter button (twice). Scott...
Thank you very much Scott, I was imagining that something like this would work. I tried several combinations during the powering up and I discovered on...
I use my Orbit V2 with Cakewalk 8. I am having a problem saving edited presets as SYSEX into Cakewalk. I can dump the Master settings no problem and reload...
Hi, I´ve got some Rack-modules and synths in my (little) CrAzY-SoUnDlAbS- Studio, and for many I´ve find somewhere in the www some User-Presets to download,...
MF/MDG Ive experimented a bit with presets and made a few. Can send you in SYSEX I guess if your interested?? Ive also found that there seems to be very little...
Hi Julian, I didn't make any of my own presets yet because I didn't have time to that, but let's start a project using resources from Orbit V2 I'm also in...
... don't ... I've got Cakewalk 8.04; probably the same. You mention the Controller Out goes to the Orbit and the sequncer. How is the sequencer connected to...
hello, I really want to buy a Orbit v2, but I don't know the price for that. Could you tell how much will i pay (approximatively) for a secondhand orbit v2 ? ...
