The 1940-1951 Mufflers that Starklite Cycle manufactures have a baffle system in the muffler. The baffle system was custom designed to provide the proper back ...
Steve You can shot peen the heads which tends to close the pores of the aluminum so they take more time to get curded up. I also use VHT Clear hi temp paint ...
michigander1951
michigander1951@...
Nov 1, 2006 9:08 am
95235
Hi Rob It has a seal on the bottom, and just slips over the return tube inside the oil tank. It has a place at the top to hook it and pull it out. Works real...
Fits over the return line. Regards, Jim Jones ... From: rob To: VirtualIndian@yahoogroups.com Sent: Wednesday, November 01, 2006 1:46 AM Subject: [Virtual...
Hi Jake I am too embarrassed to post. I have the Chief done for the last two years and only put 75 miles on it. I have been riding A H_ _ _ _ . I still...
I can second this. Regular polyester powdercoat works great. The only kind of powdercoat that I could never get to stick in high heat applications is high-heat...
... I have a small powder coating setup that uses a home oven for curing (an old one I have in the shop). I use the high temp powder on exhaust systems and it...
Thanks for the info. If memory serves, Ollie cams can be used with standard followers correct? [Non-text portions of this message have been removed]...
maus38147@...
Nov 1, 2006 3:17 pm
95245
... Not sure but I think Markey was making them John...
I have always advocated using them with stock lifters however lately there has been some disagreement on this. I have several sets of Ollies in stock if anyone...
No gang, it's not Barry. But I did some research and know exactly who he is and where he lives (right off the 105 at the Atlantic Ave exit in Lynwood Ca ...
The California page on www.lets-ride.com has been updated. Recently entered events on the California page are marked as "New Listing". New items listed: 1st...
From Barry Illert .Hi there everybody , I am still a member of the list in good standing and don't need defamatory stuff like that .Regards ,Barry ....
Barry Illert
barryil@...
Nov 1, 2006 6:25 pm
95251
From Barry Illert ,Thanks a lot you xxxxxxxx xxxx xx xxxxxx .I am not Mary ,and am still a member in good standing .Regards ,Barry ....
Barry Illert
barryil@...
Nov 1, 2006 6:30 pm
95252
How did u know? u must be berry illert also ... From: jim walter To: VirtualIndian@yahoogroups.com Sent: Wednesday, November 01, 2006 6:58 AM Subject: Re:...
Oh and by the way I'll pop off all I want. ... From: Xoutbob@... To: VirtualIndian@yahoogroups.com Sent: Wednesday, November 01, 2006 7:54 AM Subject: Re:...
Go ahead , give them my address and tell them to come over ... From: Xoutbob@... To: VirtualIndian@yahoogroups.com Sent: Wednesday, November 01, 2006 7:54...
Hey i'll save you the trouble, if some one has a problem with my opinion on glass beading and feel the need and to talk to me about it. My Phone # is 310...
Hey Michael and Fred: Thanks for your reply on this. I just want to be sure I was clear on this, so to reiterate, I am talking about the inner surface of the ...
Thanks, remarkably the quake didn't do all that much damage for 6.9. The California Loma Prieta quake was the same size and did hundreds of times more injury....
Gang, I have been at the Internet game and message boards since the early days of Bulletin Board Systems on 1200 baud modems. In every group there are the same...
Hi Jeff I have also wear at the castings at the frame , did buy new mounts. Have problems with this when mounting the bracket for my sidecar , the frame legs...
Jeff, If the 5/8" front motor mount bolt was loose during the life of the machine (common), problems will occur with the wearing of the motor mounts, the...
Great point Charlie, My powdercoater actually told me to do any cylinder work first ie: boring, porting etc... he would be masking and plugging anyway. I would...
Steve, I've never powdercoated the heads. There are a number of ways you should easily get the oil stains out. If painting or powder coating I would figure...
