One problem with replacing a qtrack case is that the newer (fulltime)cases do not fit the trans and they are mostly drivers side drop, Qtrack was always...
Well if your interested i have a builder 360 for the right price FREE, that im getting ready to just haul to the dump ive tried giving it away b-4 but no ones...
On my way home after posting my GW for sale, it crapped out, don't know whats wrong with it, but it still starts, just won't run right, anyway, the forst $500...
CFSJA Emailing List What, Rules, Who, Tips Updated 4/14/2003 ** Please SAVE THIS MESSAGE somewhere after you READ IT ** ... TABLE OF CONTENTS =================...
cfsja@yahoogroups.com
Oct 1, 2003 3:22 pm
41634
... A bumper/frame mounted carrier is definitely stronger and longer lasting. At the time the valley unit was $135 compared to $500 for a custom frame mounted...
... As a builder? If not, maybe try to find a running 401? ... It doesn't cost significantly more to do a 401 versus 360 from what I've heard. Figure $2500+...
From what I've read of everyone posting, 80's rigs -tend- to get about 11- 13mpg, the 70's rigs in the 8-10mpg range. It'd be interesting to gather real ...
The 401 block has extra webbing too. My thought is they overengineered for the thin cylinder walls. Result: very stiff block, very strong crank -- longer life?...
I hate to be the voice of opposition, but if you are planning on spending the money, why not get a remanufactured motor and just swap the cam and get your...
Hello to all full size jeep lovers. can anyone tell me if a 360cid motor will hook up to the crylsler 727 torq flight transmision. it is hooked up to a gmc...
yes, remove the little sleeve/spacer that fits in the crank snout bloommeup2002 <bloommeup2002@...> wrote: Hello to all full size jeep lovers. can anyone...
Yes, it will. You will need the flexplate and torque converter from the 727. Rande 1980 J10 1989 Comanche ... From: "bloommeup2002" <bloommeup2002@...> ...
I found a guy who will haul away junk cars for FREE!!! By Friday afternoon, it'll be gone. I don't think I'll be able to watch him drive away with it... I DID,...
It could have something to do with the additional emissions equipment and specs as well. As much as I hate to admit it, usually lower emissions also means...
Absolutely, but you will have to remove the crankshaft bushing from the end of the crankshaft. The snout on the TH400 torque converter is smaller than the 727...
I've wondered about that too. Didn't some years have 727s with a lock-up torque converter? That could definitely help mileage. Also, IIRC, the TF had a lower...
... Early 80's only, as far as I know. By 84 (maybe sooner) they ditched 'em. ... Oh, duh, forgot about that entirely. The 80+ used no lower than 3.31:1, ...
The 74 to 79 TH400 from a Jeep has an AMC pattern. The 67-73 TH400's had a Buick bolt pattern. One may be able to use a Chevy TH350 or TH400, but the...
If one FORGOT to put in that bushing, could it cause vibrations on hard acceleration and deceleration, but not at cruise? Or would the whole thing just crap...
The voice of opposition is always welcome Phillip. But... :) I am not a big fan of the rebuild companies (I think Napa uses Marshall) because I don't think...
I had heard that the early model th400 (67-73) were actually a universal bolt pattern and had an adaptor ring to the engine it was bolted behind, even the...
There is a TH400/Buick 350 at Pns right now. As i recall, these didn't have adapter rings, but I'll try to get there to verify. I'd bet there is no adapter....
... be in town ... on ... not, really. hmmmm, i am beginning to get suspicious!!! *g* Well, with Ethan out, that leaves Phillip, Scott and myself. Phillip, ...
The *forgetting to put in the bushing* is only an issue if you are putting a newer engine into an older chassis. Example, putting an 84GW 360 into a 79 J-10...
