Last I knew, these guys seemed to be a good choice, http://www.racetep.com/toystart.html Sean Estes Trails Less Traveled 831.423.5060 310F Locust Street Santa...
Sean Estes
punkassean@...
Sep 1, 2004 6:22 pm
100130
Raphael, You can try calling Fumio Fukaiya Enterprises in Riverside, CA. I got my head and block machined from them, valve job, overbored block and a mild port...
Hi Stew, I really gained a lot from the maintenance section of your site with regard to removing the turbo. The only point I would make is that I did'nt have...
(1) the atmosphere is friendly and relaxed. We do not welcome abusive language or profanity. We are also thankfully short on flame wars, so let's keep it...
gt4@yahoogroups.com
Sep 1, 2004 7:35 pm
100134
I felt the ST165 has more natural handling vs ST185's little understeer. Other than it, IMHO the ST185 is a better car in many aspects. Arvin. '93 ST185 A...
Arvin Dharmawi
gtfour21@...
Sep 1, 2004 7:49 pm
100135
Ya, go with what you like. I own one of each, and like each for different reasons. My st165 feels put together better than my st185. I think it's just a late...
Josh - 185 Performance
josh@...
Sep 1, 2004 8:07 pm
100136
... Hi Chris; ... The definitive answer is here... http://member.newsguy.com/~gtfour/ http://member.newsguy.com/~gtfour/modERL.htm ...
Den 2004-08-31, skrev pinsx3 om [gt4] st165 vs. st185 : p> I am looking at a couple of alltrac turbos. I am partial to the p> looks of the earlier cars. Am I...
Glenn Bjorcken
glenn@...
Sep 1, 2004 11:57 pm
100138
Guys Dont forget that on a CS there is an intercooler ECU and the main ECU. As far as I know the error code 54 can be caused by the level sensor in the ...
Hi Guys, I have just fitted a manual boost control valve between the hose from the turbo to the actuator. The more I open the valve, the smoother and swifter...
Hi, This is exactly the sort of solution I need!!! If you could sort out exactly which line to cut and which pin(s) to ground, I'd be eternally grateful! :-) ...
Hi I have hered all theories about dump valves and weather they are good or bad! So I have decided to find out for my self and take mine off to see what effect...
All you need to do is block the t peice you have coming from your turbo to ic or put a normal hose back on in its place. and the vac pipe coming from the other...
Take the d/v off, the exposed whole in the pipe you can blank off (you can buy the pipe end, or blanks for a couple of quid from any decent samco retailer), ...
... Hello Chris I must admit to being less than satisfied with my Dump Valve, a Bailey DV26 fitted to an ST185 Carlos Sainz. Sounded like truck airbrakes when...
Hi There, Is it imperative to remove the UK drivers side bracket that supports the cat. With it removed, will I get enough lateral clearance to slide the elbow...
iv been seeing a st165 in the auto trader, its 3000 but needs a 1500 direct point ignition system to get it runnning, it has pretty much everything you can...
iv been getting error code 52 eg knock sensor, iv heard that if your timing is off it will send that code along with the starter signal code im getting, im...
Hello everyone, where can i get a caliper rebuild kit for my front and rear calipers? and whats the cost? Thanks Amrit Trinidad JDM 1990 Toyots Celica gt-4...
Hi Guys, my car is behaving very oddly of late. Sometimes the car will not go above 2000 rpm while driving. It feels like there is a governor, like on little...
Belay my last. I sorted it by taking off the a/c compressor which gave me better access to the bolts. The turbo is off now. The strange thing is the turbine...
If the engine revs freely but stutters under load then I would be tempted to check the spark plugs and HT leads and then the coil, as a first port of call. ...
No, that's not true! You may experience knock if your timing is off (and for a number of other reasons), but this WILL NOT result in code 52! ECU will only...
hi just got a dump valve and the bits but no fitting instructions can any one tell me where the small pipe joins to, i have looked on the web but no joy. ...
Dunno if its any help,but when i fitted my dump valve,instead of cutting a hole ring off of my intercooler,i just cut a good sized'mouth' where i wanted the...
