... Doh! It hasn't been documented in detail -- not that I can find anywhere. Ya, I know the pre-turbine pressure is awful, but I want to know HOW awful, at...
We just got a small shipment of HPC-coated Aussie Exhaust downpipes in stock, right here in Colorado, for the st165, st185, and sw20. ...
Josh - 185 Performance
josh@...
Oct 1, 2004 7:45 pm
100402
(1) the atmosphere is friendly and relaxed. We do not welcome abusive language or profanity. We are also thankfully short on flame wars, so let's keep it...
gt4@yahoogroups.com
Oct 1, 2004 8:11 pm
100403
We are not telling what we do to the exhaust housing. It tooks us about 2 years to pinpint the restriction. I can say that the modification is a CNC machining ...
... Its a modified stock housing. ... Been there done that, you won't be happy with the lack of quality in he T'nex exhaust hosuing. Aaron ===== Aaron Bunch...
It is good to be back on line after so long away due to a blown up home computer. The ST205 is running sweetly. Greetings to Brian Melket in the USA. Just one...
Sam, Once the squeak is coming from the engine bay, then it's most likely the throw out bearing, and the only way to stop it is to change the bearing, BUT (not...
many gains to be had with porting the stock st 165 ex manifold? Steve Gillies ST 165 88 uk (BETSY) 293 BHP West Sussex msn: quickdrawmcgr30@... ... ...
it may be possible to get some spray on grease thru the boot cover and onto the bearing? stew uk ... likely the throw out bearing, and the only way to stop it...
hi all is this possible? a st 162 side inlet manifold on the 3sgte? does it bolt up ok? the WRC corolla had a side feed, must be something in it? TIA Steve...
- hi all is this possible? - a st 162 side inlet manifold on the 3sgte? - does it bolt up ok? I am not sure if the ST162 manifold is the same as the ST165...
It should bolt up fine. I have a first gen 3SGE intake manifold and it fit onto a 2g head with no problem. Seems like the distributor cap might be an issue...
I am using a ST182 manifold in a ST165 engine, not the ST162... ST182 manifold has a better design, and was what I had. It doesn't interfeir with anything,...
surely it would have been far easier and quicker to just shield the fmic pipe as it goes over the engine lol?? would have took 10 minutes and cost very little...
stew, my idea is purely based on other engines and what has been discussed on here over the passed years.. the corolla wrc car used side feed afaik as does the...
AFAIK = As far as I know Mike Kelly ST205 UK ... From: Stephen Ault [mailto:s.ault@...] Sent: 03 October 2004 18:06 To: gt4@yahoogroups.com Subject:...
... From: "Mike Kelly" <michaelskelly@...> ... hehehe im being watched by quiet uk owners :-) there goes my secret plans...lol Steve Gillies ST 165 88...
- surely it would have been far easier and quicker to just shield the fmic pipe as it goes over the engine lol?? Yeah! Sure it World be easy, but it was...
i am toyota fan I currently would like to own a Carlos Saintz version of the Gt-4 .I am willing to purchase one that needs a lot of work. or mechanics special....
Hey gang, Ok, I had to clear this up because people were sending email wanting 185 bits. I have 165 parts. Rear xbar is brand new, front was installed for ...
Hi Group, Installed a newer engine and trans (56 kilometers on the clock) in my 90 st185us with a "clutch masters fx100" clutch. Of course I bled the clutch...
I had the same problem with Redline Synthetic gear oil. I switched to Pennzoil Synrchomesh from the local Autozone. The transmission has not grinded gears even...
Hey guys, Just wanting peoples 2 cents and experience on a fuel pressure regulator. In the past few months we have blown two knock sensors and I believe its...
... The Malpassi is a 1:1 regulator with regard to compensation for boost, it has a RESPONSE TIME that is 1.7 times quicker than most stock regulators. I have...
