i checked out the exhaust manifold..and the noise seems to be coming from further back...i cant see this being the inlet manifold problem making that noise can...
(1) the atmosphere is friendly and relaxed. We do not welcome abusive language or profanity. We are also thankfully short on flame wars, so let's keep it...
gt4@yahoogroups.com
Jun 1, 2004 12:14 pm
99554
Isn't it 0.8 mm?? Rommel the iCeMAn 1992 Celica GT-Four (JDM wide-body) Barbados, Caribbean....
l have posted this message in the convertible group with no sucess, however, l know that some owners also use this group, SO......... I am after details of...
Looking good Lionel, made a good job of it Here's another mini project for you :) The ST185CS's & RC's, along with the ST205's use a limited slip rear diff,...
Hey Tim Have you checked the front diff mounts? I had a similar problem on my car a couple of years ago - turned out the front diff mounts had collapsed.... On...
Hi All Info for the archives.... For some time I have had error code 54 which we have tracked down to a faulty armature in the IC pump. It still works but at a...
The rear diff has been changed too. unfortunatly after 150km it broke (because it had received a shock on the preceding car). so I put back mine. but after...
Tim, I had exactly the same problem. It'd make a thump if I didn't change the gears slowwly. It was the rubber mount to the rear of the rear diff. Is that the...
Yep already changed the diff mount, this ones not that simple unfortunately. Tim 87 ST165 pre-facelift 91 ST185RC 92 ST185RC Auckland, New Zealand--- In...
I had some bad thumping, I thought it was the diff mount or the drivetrain somewhere, but it was actually the rear lower control arm bushings in the hub. My...
Jon
supra@...
Jun 3, 2004 4:31 pm
99567
If the head doesn't need any machine work, how difficult is it to replace the valves, springs, retainers and doing the MRS lifter conversion? Are there some...
Hi there, http://www.cyberauto.com/index.php/ToyotaMR2SW20(90-95).txt There are some Greddy devices listed there, but intended for the MR2, and I'm not sure if...
Jeremiah, Out of curiousity, why do you want the MRS conversion? Valves/springs and retainers aren't that difficult to do. You seem to have done a lot already...
Are you looking for porn this evening ? Well these are the best links for Free porn. No credit card, No checking account no details All sites are free with...
What is the temperature (exhaust temperature taken in the manifold) that starts to destroy the engine? Inquiring minds want to know! -- Bill Price '93 ST185 ...
Hi there, http://www.cyberauto.com/index.php/ToyotaMR2SW20(90-95).txt There are some Greddy devices listed there, but intended for the MR2, and I'm not sure if...
Can anyone tell me if the 2nd gen head is different on the intake side than the 1st gen? I need to know if the TVIS plates are the same. Thanks, -Alex...
Alex, Yes, you can swap between the two manifolds no problem. They have identical bolt patterns. ... Chris Dittrick 1988 ST165 http://www.gtfour.ca ... side...
Hi everyone, I had my Grp A dynoed a few weeks ago and got a huge shock at the results. I always felt my car was not up to scratch but it only produced 90kw @...
Timing might be a problem, but the ECU ignores the o2 sensor at WOT so it should not lower the power output in the peak area. Robert...
Robert Pina
robert@...
Jun 5, 2004 9:31 pm
99579
I had the ignition pulse timing sensor replaced because it was faulty. It brought up the 'Engine fault light' on the dash before I replaced it. The light is...
Planning to do side feed? I am planning to pick up a 3SGE manifold and do it. We will see though. Kevin Hall 5-tone ST185 So. Cal ... From: "Alex Amaral"...
hi, i have just purchased a st185 gt4, it has a close ratio box and a freind of mine said it could be a rally model.Is this true?The model no is e-st185h blmvz...
