The following is copied from the FAQ at Synaptics Touchpad driver page http://w1.894.telia.com/~u89404340/touchpad/ * Does it work on a Dell Inspiron 8200? No,...
Hi, Dell TrueMobile 1150, works on Libranet 2.8, SuSE 8.2 right out of the box. Uses Orinoco chipset with the PCMCIA_ cs option. I have not tried any...
if ya got a chance check out my new group... its for anyversion of Simcity.. or derivations there of.. regions, cities, and game tips and discussions are ...
You might try checking the alsa mixer to make sure that nothing is muted. I had the same issue with dvd's on my laptop in gentoo. HTH ... From: steveh7676...
Not answering the read-only issue, but if you are intending to regularly backup from one drive to the other, consider using rsync instead of cp. If you want to...
Hi, My Inspiron 8200 fans are making some odd noise. I press "Fn-Z" to reread the temperature and it stops for some time. $ cat /proc/i8k 1.0 A10 BXXXXXX 2 2...
Hamish, "fdisk -l" command returns the following: /dev/sda1 /dev/sdb1 I have two external SCSI (maxtor) drives and i respectively mount them to the following...
Hi Amjad, Well I'm scraping the bottom of the barrel here but try running hdparm -r /dev/sdb Instead /dev/disk2 since hdparm is designed for setting device...
Silly question, but has the OP tried reading the output of 'dmesg' when the disk is in read-only mode? I'm wondering if it is pulling some kind of error...
... Hash: SHA1 ... * Try removing the dust from the fans using a spray duster * Check if some screws on the bottom of your chassis are not correct mounted ...
mchristoph.eckert@...
Aug 2, 2004 3:14 pm
24733
Well you got my curiosity up! I have a Insprion 8100, running SuSE 9.1, and sure enough if I press the Fn-Z keys, my fans immediately stop running also! I am...
The Synaptics drivers don't seem to on the 8200. What should I do? ... page ... be ... until ... engineer ... have ... box ... So ... on ... now. ... nusence...
I've got Slackware 10.0 running just fine on a Inspiron 8500. I've got two main issues, though. The first is I have no clue how to setup acpid to properly...
I have found out thur much hard work that Linux just isn't worth the trouble. I have tried about every flavor out. And while the insall on konppix and mandrake...
As you have said most of the things work in linux. For modem it is the problem with dell selecting a vendor having closed source soft modem like bcm or wifi...
... I just want to echo some of your frustrations. I have experimented with Linux in many flavors for a number of years. Like you I can get some of it to...
... Hehe, I wish I could say the same about windows, since getting my M60 the wireless card randomnly stops working in Windows needing a reboot to get it...
I've asked before, but does anyone here have suggestions for an 802.11g wifi miniPCI card that works in a dell C600 Latitude? The Dell one they show for...
You have you tried the ndiswrapper???? I use it with Linksys 802.11g card with Fedora Core 2 and it was pretty easy to set up and so far no problems. ...
No, I hadn't. I've tried to support companies that release specs. However, I may have to break down and try this, if no one can recommend a good miniPCI...
... Same here. It's a bit of a pain, but I finally decided to go with a PCMCIA card for wireless rather than going the ndiswrapper way. I've got an SMC...
The SMC 3635W is 802.11b, there are plenty of chipsets for 11Mbits that have open source drivers. I myself used Orinoco cards before going to 54Mbits. I am...
... http://www.prism54.org/ but they do need a non-free binary firmware that is uploaded to the card (I think, I havn't actually used one) Adam -- jabberid =...
I'm not sure about the 11g, but Orinoco based cards work well. (Dell should be able to tell you which of theirs is based on it) The miniPCI card I use in my...
I can't say for MiniPCI (I'm still patiently waiting/watching Intel's progress for my 2200 BG MiniPCI card), but Madwifi does cover my D-Link DWL-G650...
