i have a motorola mts2000 radio that i bought on ebay. for some reason it wont power up. could anyone tell me what is the cause of that. thank much....
Can you guys help me out? I am very interested in purchasing a TK-760G 128 channel VHF radio and understand that it like it's predeceasor, the TK-760, can be...
Can you guys help me out with this one too? I am very interested in purchasing a TK-270G 128 channel VHF radio and understand that it like it's predeacesor,...
... fully ... have ... help ... if you do the mod to it it will be fully front panal programmable all exept for alpha tags , this must be done by pc ONLY...
Hi everyone. Ive recently commmandiered a Midland 70-1562B UHF Mobile radio and need to know how it gets programmed. Is it software or a EEPROM? If anyone...
I think the term "front panel programming" is misleading, because it is a very laborious and time-consuming process, and it is definitely not user-friendly. ...
A Midland LMR needs a programmer OR PC software and programming cable to be programmed...(All Midland proprietary stuff of course).. I have a copy of the...
Trying to figure out what RSS software to use with this radio. Model is D27MQA5GB2AK Is it the standard radmob software or do you need something else to...
Hello Folks, Looking for info on the cable for programming a Tekk NT-8. Prefer to build as I have Maxim 232 Chip. I usually build most of my programming cables...
The possibilities are numerous. Are you sure you have a good battery? There is a fuse internal to the radio, but you have to be fairly experienced in...
I am new to this 2way radio stuff and have a Kenwood TK-730G with 160 channels and four programming buttons on the front ( D/A, TA, AN, & SP ) that I have no...
I am in the process of helping to rebuild an old ambulance into a comm van for Jefferson Co., Colorado RACES. From what I found on the Motorola site it looks...
Jeff, I believe that the RVN4019K RSS is the right one, but the best way to know for certain is to call the Motorola Parts ID desk at 800-227-6772. Give the...
Hello, Trying to help a local public service agency reprogram some of their Kenwood TK-730 radios. They have the appropriate software, but they don't seem to...
Just received from Medical Emergencies Group a Yaesu model FTL7002. First time I see this specimen...looks like a collection item...I don't know...anyway, does...
Having problems to program GM300, Model:M33GMC00D2AA, Manufactured dete:9512 (Malaysia). Program reads codeplug but it is not decoded. Computer freezes at...
Can anyone in the group walk-me through the steps on how to change or add additional channels from my MT-1000 from 8 channels to 16 channels? I have inspected...
I have a question on a aftermarket RIB box I have... I've attached a picture of it at http://www.espphotography.com/rib.jpg - question one is where can I...
I already tried this.......peeled it off and attempted to lift the pin gently by using a longnose but wouldn't cooperate...I will attempt again applying about...
I think I just broke off the small tab on the channel selector knob. Then I think there is a programing thing you do (change the model number and save the new...
Your best bet is to open it up and take a look inside.. it most likly has a voltage regulator in it, should be a 3 pin chip with something like LM7805 on it....
Hi all Does anybody have the interface schematic diagram for Standard GX2000 programming? I believe it's uses an MAX 232, but i'm not sure. Any help would be...
I got mine from www.radiocables.com, they were real fast on the shipment and the sales man even sent some info about programming the radio. I will see if I...
chris try batlabs theyhave very detailed steps for the change ... From: Chris Inos To: radio-programming@yahoogroups.com Sent: Sunday, February 02, 2003 5:47...
try first and see if the software will let you add more modes. In one i did. All i did was remove the stop and added the extra channels up to 16 by ADD MODE....
