I have a shinwa SC425YB repeater that i can swap to programmingtools to same radio, programmingcable/software, usermanuals, skemathics, mic, and other...
does the radio even act like it is being programmed? the display will read "programming" or something like that. I had a similar problem to this a while ago. I...
Hello, I have played around with many of these radios and I think yours might be a firmware issue. Check what version of the firmware you have by holding in...
... problem is many 2020 series II are not series II at all but series I with a II head fitted I had one series I will not program with windows software, I...
be carefull with upgrading firmware to your radio. SII use a diferent logic pcb, if you set a older radio with new firmware may be the radio go off....... Best...
Hi. Do a search in Yahoo Groups. There is a group that many on this one also belong to called PMR Group. on yahoo groups. Never seen anything like that being...
Well I just spent £40 on a gp340 and I have little electronics knowledge, I can follow a diagram but I cant design and modify equipment and I thought seeing...
Ok, so I took apart the connector on my kpg-36 programming cable. As a point of reference; there are a total of 17 pin positions on the connector. 3 of them...
Hello Not sure if this is the proper place to ask this... please ignore if it is not. I have CPS 3.0.1.0 for the Motorola HT750/1250 HT. Unfortunately, when I ...
http://hamradio.online.ru/ftp/dw.php?sl500.zip mike ... Email sent from www.ntlworld.com Virus-checked using McAfee(R) Software Visit www.ntlworld.com/security...
I have a standard HX580T handset and I want to program it for the Knoxville, Tn PD freq's. I work security and it's nice to know what's going on around me and...
It appears that Knoxville, Tn PD is on a motorola smartnet system. You will not be able to program a Standard radio to monitor that system. You would have to...
Hi all, I have a couple of questions for the group. First, will the programming cable for the Relm RPV599's work on a Kenwood TK-2160? I know I have seen this...
Ned, You can pick up a ribless programming lead on ebay for $10 upwards + postage. You just run KPG82d and switch the 2160 on and read it. Duncan London. ... ...
Hi All, Does anyone knowc how I might get a T800 that is normally 440-480mhz down on to the Ham band, 430 to 440 ? PGM 800 rejects frequency entry below 440...
I am not real familiar with Maxon radio's and a friend gave me a Maxon "SP-140U2" radio and asked me if I can program it for him. Does anyone know what is...
Hello Which software are you to use on the TK860H Kenwood Radios? I thought I had used the KPG29D that works with the TK860 radios before but every time I try...
Aaron D Schmitz
aschmitz@...
Jul 3, 2006 5:18 pm
38703
If your radio is a TK-860H then that software should work. If your radio is a TK-860HGK then you need the KPG-56D software which is in the DOS and windows...
I have a repeater with Shinwa SC425YB (Zodiac MA425) and looking for howto program it, the WWW.VHF.NO, they innport and sell icom, here in Norway did sell it,...
hi is there any one that can help me i need some info on this cleartone cm 7000 ??am/fm/ how do i switch from uhf to vhf on this radio??it as a fm/am bord...
its sp140v2 you will need this http://www.maxon.com.au/products/industrial/industrial-lmr-portableradio-sp140-software.asp dunno about the lead but the SL130...
