I have a CDM-1250 & 1550 and both are remote mounted in one car, I'm using a Octopus rib and I can program the radios just fine when NOT remote mounted, I get...
OK, Dan, I've "sorta" followed your journey but I'm not sure of where you are right now... I'll offer this anyway. First, did it work properly with the...
I have a mt2000 portable. It is programmed with version 02.04. Does anybody have this version? Is it possible to get a copy of it. You can e-mail it to...
Hey Guys, i'm not exactly sure what dosbox is but if your not running in PURE DOS as in DOS 6.22 on a slow pc your probably out of luck for programing from...
Hello all I have decided to sell my 70-1000 programmer; I no longer have any Midland radios, so it's surplus to my needs. Comes with ac cord, instruction and...
hello all well in need of software for my old ic-f40 ht. i can't find my copy and beside's going to russiaetc.. is there anyone that can help?. also i still...
I have always said it pays to hang on to older technology sometimes. So many of the radios from the early to mid 90's will only run on pure DOS. I use an old...
muliti cable After market rib for many different radios, I use it for my Maxtrac, CDM, HT-750 and some other radios that I'm not sure of ... From: ian dean To:...
Yeah, I created a DOS boot CD and can program the radio from my laptop after booting to DOS 6.22. I just wanted to see if there was a way to do it within ...
Why don't just setup your computer to duel boot and you will be set. Jerry, Crest47 WPXH 766 / W6JFS ... You rock. That's why Blockbuster's offering you one...
Wouldn't I have to repartition my hard drive and reinstall XP to do that? In a message dated 4/1/2008 10:02:46 P.M. Central Daylight Time, crest47@......
The size of the disk exceeds what Dos 6.22 is able to see I would believe. I have had the same issue with an older ( )ell laptop and ended up putting a ...
I am looking for some scrap, junked out Vertex FTL-1011,2011,or 7011 mobile radios for parts. I need the front panel display board from a 24 channel unit to...
hi all I have CPS R06.04.00 and i get a error message when i tried to read the radio "Unsupported Model" and next it says "Application does not support reading...
Yeah thanks for that,i actually had the picture sent to me.over here its known as a multi rib,there notorious for not programming when the 9v battery is...
Dalton It is programmed from 450-512. It is all programmed conventional. Thanks Bill Dalton <dalton9691@...> wrote: depends. can u do trunking and not...
Oh, that would be the problem. Either way, I do have an old desktop computer that I can use but, I don't have it right now, would have to get it out of ...
if the radio came 450-512mhz, then you're stuck and I know of no way of changing it ... From: Dalton To: radio-programming@yahoogroups.com Sent: Wednesday,...
Does anyone have a copy of the Service Manual for this radio ? I am trying to confirm the pin-out for the programming connector. Thanks, Dick, W1KSZ...
Does anyone have the chart depicting the DIP switch channel settings for the Tait T800 Series repeater? These are programmed via EEPROM and the DIP settings...
Actually the switches point to a channel slot in the prom by number between 1 and 128 in binary... The prom has pre programmed info that may or may not be what...
Anyone ever ran into this error code. I am in the process of updating this software so if that is whats going on I am fine but if not I need to know what the...
Anyone have a definition for this error code?? I am updating this particular software so if its a code plug version issue Im ok..Otherwise I have some work...
