My vehicles weigh as follows: 89 Mustang 2.3 5 speed LX hatch (when stock) - 2880 lbs with half tank of gas 91 Mustang 2.3 auto LX coupe - 2960 lbs with half...
Ryan, You need to step up to a V8 :^) ... Thanks David Fincik 89 Mustang LX, A4 331 Stroker, 325rwhp. 360rwtq, Full Griggs, Cobra brakes w/ABS Yahoo Racing...
i know it's called a 7 quart pan, but somewhere recently, and i don't remember which list, someone, maybe darius, seemed to imply that the 7 quart reference...
You do have to take into account the filter and cooler (if equipped). My Moroso 7-qt pan with filter and cooler actually took 8.5-9 quarts. Howard Bennett ... ...
YES, yes, yes... This summer I finally got the '89 out to the local drag strip and ran consistent 14.5's at 93 mph, kind of a birthday present to myself, and ...
so, how do you do this? obviously, i have a filter. also, i have a griffing radiator with the built in oil cooler, [real stacked plate oil cooler, _not_ a...
Griffin can probably tell you the capacity of the cooler, and then add in some additional volume to account for the lines. I remember finding info somewhere...
... This means that you fill it up with 7 quarts, let the oil all drain into the pan (say, overnight), and then mark that level on the dipstick: that's the...
My 86gt weighed in at 3150lbs on longacre 4 corner scales. Its non a/c, backseat delete, 4 point road race cage, subs, panhard, strut brace, and cobra r's. It...
I had a 79 V8 k-member that weighed quite a bit more than the 86 that I replaced it. From what I understand about the k-members, the later cars had a wider...
does an arp main stud kit come with washers that go under the nuts? i'm in the middle of my first engine build that i actually did myself. i've r'n'r'd a...
...my arp oil pan bolt kit? it will be on a canton road race pan. the bolt kit comes with flat washers, but not split-rings also, do i need split ring washers...
My brother's '99 Explorer Sport (4.0L SOHC, AT, 120k miles) has the O/D (Overdrive) dash light flashing and staying lit intermittently. He told me it usually...
I am trying to prep my 67 Mustang this month and next to run some fun-only opentrack/HPDE with NASA-SE, and was wondering if theres a reasonably comprehensive...
I am running a 1968 GT/California Special with Nor-Cal Shelby club. My mods are few: Shelby drop, 1 1/8" front sway bar great sticky street tires on 16 shelby...
I am running a 1968 GT/California Special with Nor-Cal Shelby club. My mods are few: -Shelby drop -1 1/8" front sway bar -great sticky street tires on 16...
Sorry to repost - did not finish the first time! I am running a 1968 GT/California Special with Nor-Cal Shelby club. My mods are few: -Shelby drop -1 1/8"...
... Even for casual open tracking, get some good brake pads. The Minimum is going be the Performance Friction, and fabricate up some brake cooling ducts, even...
griggs, baby! check www.griggsracing.com and look at their gr350 stuff...and drool. seriously though, for your first few times out, just make sure you have...
www.windsor-fox.com bankers hours, 9:30-4:30, closed fridays and weekends, no way to order online, over 24 hours without a returned phone call, answering...
I've dealt with them. very nice lady took care of my order. I bought a speed density to mass-air conversion wire kit from them(I'm just inept when it comes to...
I'm combining a few questions that are related to each other in my case. This would be for an '04 Cobra driven hard at open track events. Should I ever trust...
On Thu, 30 Dec 2004 18:40:57 -0800 (PST), Theodore Chen ... I don't know about the k-members but only some cars got the aluminum bumper supports. 79 Capri...
On Sat, 1 Jan 2005 15:11:03 -0800 (PST), Ryan Modos <rmodos@...> ... Weren't you the guy who was putting a 2.0 turbo Zetec into a Mustang? -- I'm sorry...
Depends on the accident. As someone who raced an earlier Cobra for 5 years in the SCCA. I had one hub assembly go bad in that time. I had one hit on the left...
many thanks for the input, it looks like I may be pointed in the right direction, at least for starters. Eric __________________________________ Do you Yahoo!?...
Thanks, Kent. As a follow up, are there things I should look for in a bad stud besides thread damage or being broken? How about things I should look for in a...
Yeah, I still have it (the 2.0 Zetec), and it's still a possibility, but at this point I just see it (in a Mustang) as more a novelty than anything and am...
