Yeah I forgot to mention that (really didn't think anyone was going to mention it) I have already made a pickup for the tank and have an electronic fuel pump...
CMC is a mixture of carbed and FI cars, with the majority being FI. I agree about getting a good fuel pump - my 85 GT CMC car uses a Holley Blue electric. Adam...
Guys, Kind-of on topic here (put not to completely high-jack this post) for those of you that are in CMC or AI/X..... I really need to sell a race motor that I...
I did the conversion from EFI to Carb once myself - and regulating the EFI pressure down to Carb pressures was a major headache. If you can remove the...
I know it's been a while since I went over this but isn't it better to go with the SN-95 control arms? George. ... From: rrax-mustang@yahoogroups.com...
George Kokolakis
rgbcons@...
Jul 1, 2005 8:17 pm
33653
All I know is that spacers have failed repeatedly because the wheel hub face is bigger than the spacer and/or the spacer is smaller than the hub. This causes...
George Kokolakis
rgbcons@...
Jul 1, 2005 8:23 pm
33654
All the over the counter spacers I've seen or bought are exactly the same size as the hub and wheel or even slightly bigger if used on 13-14" wheels. And yes a...
Guys, I am looking for a set of coil spring spacers, about 1/4" for the front springs on my 1992 mustang, to raise the front of the car up. I feel the front...
Hey Chris, Instead of spending more money and adding to your car, why don't you just take a small amount off the rear springs? If you were to cut a 1/4 coil...
When I bought my Steeda X2 ball joints they included a pair of spacers to do what you indicated. You might try Steeda and see if you can buy a set seperately....
heat it with a blow torch Oh man I would not recommend. Ron ... From: rrax-mustang@yahoogroups.com [mailto:rrax-mustang@yahoogroups.com] On Behalf Of Doug Van...
Ron, Ron, Ron, Ron, Ron, You only use the torch to heat up the very end so that you can flatten out the part of the coil that sits in the bucket/perch........
This may be a day late and a dollar short, but I used a kit from a place called The Streetrod Manufacturing Co. Inc. to put rear disks on the back of my '71...
grossen@...
Jul 6, 2005 2:35 am
33661
I have the adjustable rear control arms from MM so the rear is not the problem. I will look into a machine shop to make a spacer. I will also be buying a set...
Just doing a little mid summer garage cleaning. Need to get rid of 4 sets of tires. 2 A3S05 sets and 2 A3S04 sets. Tires located in Detroit Area. Good for open...
[[[[Is it a race setup? Maybe so. It worked OK autocrossing, eliminated that pesky rear lockup at corner entry. Pad selection is good for the metric caliper...
george, SN95 control arms are 1.5" longer than fox3. t-bird control arms are 0.75" longer than fox3. if you use SN95 control arms, you may discover that you...
Sorry for the sales pitch but I've got a K-member and lower control arms out of my 99' that I'd like to sell. It's on eBay right now if anyone's interested:...
actually, I use the 86 k member and the t-bird arms and find it a good match. I am at 2^ neg camber and I still have room to adjust. ... __ Tom Stangler, Va...
didn't intend to imply that the t-bird arms wouldn't be a good match to the '86 k-member. i'm just saying that the SN95 arms are a good match for the '86...
FWIW, I have an 85 GT, and use the SN95 control arms w/Delrin bushings. I'm able to get nearly 6^ of negative camber, but currently have it set to 2.5^ ( it...
roger. I didn't intend to imply that you intended to imply that they were not a match, which they are, that we both intended to imply. k member difference is...
yes, 1 inch difference between the left and right control arm mounts. the steering rack mounts are the same. all of the extra length is outboard of the...
Teddy, I've been thinking of replacing my control arms but with having an 86 I would rather do a little rather than a lot. If the T-bird arms are only 3/4" ...
George Kokolakis
rgbcons@...
Jul 8, 2005 5:24 am
33673
Teddy, Wouldn't you have to slot the struts to helps correct for the too much camber? George. ... From: rrax-mustang@yahoogroups.com...
George Kokolakis
rgbcons@...
Jul 8, 2005 5:25 am
33674
We bought new scales and are selling our old scales on Ebay: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=4560973275 ...
I'm not finding a lot of contact with the 86 LX/SN-95 LCAs/94 spindles/Eibach Comp Springs/V700 17x255 and -2.5 camber. The front fenders rub the shoulders of...
87-88 v8 tbird ... __ Tom Stangler, Va Beach, VA Track Car: 300HP '86 5.0 Mustang, "5.0 RACER" QA\QC\Safety Manager\Track Event Driving Instructor Now ISO-9001...
