Of price & performance? I have Bilsteins on the '96 Cobra and they've been great. I'm not that hardcore that I miss the adjustability. In looking for...
They are a good street shock, but not for AutoX or Open Track Days. L From: rrax-mustang@yahoogroups.com [mailto:rrax-mustang@yahoogroups.com] On Behalf Of Tim...
Tokico states the that the blues product in a 20% increase in dampening performance over production OEM which by the way are Tokico (sans the Bilstiens on the...
Richard! Just feeling a little nostalgic here, since we both go back quite a while here. Did you ever get that aluminum radiator I sold you unblocked? Talk...
Thanks everyone for the feedback. I'm still looking at this as a car that could be a total loss in a blink - such is the life of a track car. So I am trying...
Trust me from experience, don’t waste your money on things that you will replace once, twice or maybe even three times with inferior products. Just save the...
IMHO, spend the $$$ for the Konis and forget it. If you need to replace, and you probably won't (I had a 83 F41 Impala with 260K miles that handled fine with...
Gene Beaird
bgbeaird@...
Feb 14, 2008 1:39 am
36153
I must do some de-car-ing to move on to the next phase of my motorsports life. Asking $999. The car is in Eastern PA. ...
I have an 88 Mustang coupe that I am returning back to full time street use. I installed an Autopower bolt in roll cage since I used the car on fun days at...
for the right price, I'll take it. I'm in Youngstown, Ohio. Where are you located? ... street use. I installed an Autopower bolt in roll cage since I used the ...
Has anyone ever tried to fill up a manual trans from the shifter mount inside the car? Seems like it would be easier than pumping it in through the side fill ...
You'll have to know how much fluid to put back in. Every manual gerarbox I'f filled had you fill it until fluid came out of the fill hole. Obviously if you...
it's really not that hard to fill it from below. use a 3/8" square drive to remove the fill plug. you can buy a hand pump from the local auto parts store....
When I refill, I remove the top fill hole, leave a catch pan under the car, and then fill from the shifter area until it comes out the fill hole. Much easier...
... I've done this multiple times. Worked fine all of the time. If you need to, you could pull the plug and stop pouring when it comes out. I've never done...
that'd work. don't drop anything in there! ... From: Tim Clark <oktavius8292@...> To: rrax-mustang@yahoogroups.com Sent: Wednesday, March 26, 2008 4:20:55...
That works fine and since you have boot off, you can actually see when it starts running out instead of wasting several ounces listening for it to splash. ...
You guys are going about it the hard way!:) I use a funnel and a long piece of clear hose from ace. Hang the funnel under the open hood using a coat hanger,...
... funnel under the open hood using a coat hanger, and snake the hose to the opened fill hole on the side, and add fluid till it comes back out the...
Well larry, i've r'n'r'd my tranny 4 times...3 engine changes and a clutch, since 2002. And not a single time did I remove the shifter. The handle, yes. The...
still too hard. I plug in a small aftermarket 12 volt fuel pump, one end in the bottle, one end in the trans, and turn it on. Both hands are now free for the...
YES! YES! mmm doughnut... (drool) LOL well my shifter is off, so I'm trying it that way! ha As much fun as Pete's snaking tube with a coat hanger sounds.......
Steve-o, don't know how far your new house is from mine, but if all else fails, you can borrow my tube and funnel. I keep it hung up on the left wall of the...
No, I can't :-( I'll be in Singapore probably the first week or two of May, and then Lone Pine Time Trials at the end of May. I don't really have the time,...
Ive filled my tranny that way every time, no problem. If you are concerned about over filling....open up the fill hole after you put in the fluid to allow any...
Now what in sept could possibly be more important than a track event ;) ... From: johnysbillards <my72vette454_4sp@...> Sent: March 28, 2008 8:50 AM ...
According to the 2008 rules, 15.11 states: 15.11 OUT-OF-PRODUCTION CARS Where a car is out of production and the manufacturer is either out of business, stocks...
Probably the best way to solve this is to gateher all the information you can and send it to SCCA and let them make a determination and get it in writing....
Hi guys, I've been driving my '72 Mustang around after doing suspension and trans, wheels/tires, etc to it, and having a problem with front end grip. I've...
