The following tanzer poll is now closed. Here are the final results: POLL QUESTION: With new motor technology and as is allowed in other classes, how should ...
tanzer@yahoogroups.com
Aug 1, 2004 8:06 am
20645
I need port and starbord as well. ... [Non-text portions of this message have been removed]...
I have Arco 8 winches on my T7.5, and have had a couple of the springs and pawls break. I was able to buy generic replacement parts at our local marine store. ...
Mark Jeffrey
mjeffrey@...
Aug 1, 2004 1:21 pm
20647
... A single will always vibrate more than a twin and more pronounced on a 4 stroke. On a 2 stroke twin, the pistons are opposite each other on the shaft and...
Hi My Merc 4 also hits the rudder in the lowest detent on the drop bracket. I have since put a padlock in that setting so it brings up about 1" short of going...
FYI - you do NOT need to attend the captain's meeting the week before to be able to participate in the regatta. Hopefully, with this requirement lifted, we...
I must apologize for Xan's SHAMELESS behavior yesterday! After we and Irresponsible (Nick and Christine T28 #119) helped Bill and Barbara survey #31, the 7 of...
I think I reported a couple of weeks back that my centerboard was stuck in the raised position after going aground a couple of times (deliberately). It's down...
better still - when you take it out this winter, install a little gizmo on the tail if the board, attach some strong line and run it through a spool at the...
bridgetotoole@...
Aug 1, 2004 10:12 pm
20653
... gizmo on the tail if the board, attach some strong line and run it through a spool at the tail of the boat, to the nearest winch, and just pull it down on...
I can attest as to how spunky Xan was yesterday. A double reef in the main as well. I finally took a photo since someone lounging on the deck was almost...
I too tried out my Honda 4-stroke 5 hp for the first time today. My report is a bit different from Rick's. For one, I had a heck of a time getting the motor...
Dave, Regarding the stalling condition when you first start the engine...the yard rep told me to adjust the idle screw to ensure it would not stall at lowest...
Starting: Interesting story. I usually pull the choke out and leave the engine running for a minute or so, and then gradually push it in, as the engine warms...
Hey guys. Here is a thought. After reading the two seemingly bothersome problems about the location of the prime bulb, If it is that much of an issue, just...
TALanders@...
Aug 2, 2004 4:58 pm
20660
Put us on the list for a port lazarette hatch, please. Brian Wiersema and Pat Shannon T22 #1416, "Baffin" 301-379-4154 or 703-627-5379 bwsails at hotmail dot...
I looked at my motor and couldn't find the idle screw. Or more accurately, I found many things that could have been the idle screw. I decided to leave it...
... Twist the handle and look for the lever at the end of the cable that moves. There will be a screw and locking nut right there. [Sorry if you've already...
To all Tanzer owners: I have a 1986 Tanzer 31 (just paid for)and I am having a difficult time researching it's inception and construction data (how many made, ...
fcornman@...
Aug 3, 2004 1:23 am
20665
Fred: Here is the best info I have on the T-31... http://www.magma.ca/~tanzer22/tanzer31.htm or http://www.cncphotoalbum.com/index1.htm follow the link to C&C ...
Hi All you Motor experts, Well my honda 5 hp of indeterminate age has started to belch a lot of black smoke and leave a film of oil on the water when I start...
Hi Gang: There's an old saying that there are two types of sailors: those who have run aground and those who will run aground. I am now part of the latter. ...
David Rankin
drankin@...
Aug 3, 2004 4:25 pm
20668
... David: I would take a torque wrench to the bolts and check out if they are close to what is recommended. "A few years ago I had Johann Tanzer aboard my...
I'm finally getting to go to Atlantic Beach, NC for a few days and am thinking about bringing our T22 and either sailing offshore or in the Pamlico Sound. Any...
(I'm resending this with a more appropriate Subject line) I'm finally getting to go to Atlantic Beach, NC for a few days and am thinking about bringing our T22...
... are ... Hi all; I would check the maximum torque recommended for the bolts you have in the keel . My Tanzer 22 had 1/2-13 stainless bolts and the maximum...
I have found two rivets on deck, one last fall and one this summer. Now I am concerned about mast hardware. I have a '74 boat with an original rig. Should I...
Paul, Where are the rivets from? Boom? Mast fitting? I have a '73, and there are some rigging pieces - padeyes, blocks, where rivets clearly are beginning...
