In a message dated 4/1/2006 5:34:46 A.M. Eastern Standard Time, tanzer@yahoogroups.com writes: Does anyone happen to know what paint (colour, brand, etc.) can...
In a message dated 4/1/2006 5:34:46 A.M. Eastern Standard Time, tanzer@yahoogroups.com writes: Tomorrow I'm going to look at some teak so I can make new...
In a message dated 4/1/2006 5:34:46 A.M. Eastern Standard Time, tanzer@yahoogroups.com writes: cut away some of the plywood between the deck and the liner if...
In a message dated 4/1/2006 5:34:46 A.M. Eastern Standard Time, tanzer@yahoogroups.com writes: Try Interlux 4241 Sapphire or if you want to go darker try...
What model motor (number) did you use? ' ... drilled 2 new ... cardboard ... about 3" ... between ... on there ... washers on ... Behalf Of ... motor ... drill...
Judi & all , The Tanzer-22's sailed on the same coarse as Lazer-28's several years ago at CORK. The Lazers learned a little lesson about the skill and...
... VC-17 is not ablative, however, it goes on in such a thin coat and when you recoat what's on softens up that the build up factor is almost zero. I think...
... Repainted the boot stripe (actually raised the waterline, so painted a new boot stripe, as we got tired of scrubbing the crud of the the arra above the...
Hi Kent I am fresh water now, was using XXX while in salt water, but may go VC17. Being ablative, and my mooring being near household fresh water intake, was...
OK. I am now armed with a little more info. All this time I thought Metal Ready was used to replace the layer of metal over the keel (the one I just chiseled...
I just thought I should defend the " flimsy " factory teak handrails I sell as posted by Mr Miller. I agree they are not cheap but I think you explained why in...
... VC-17M, still leaches a lot of copper, so not sure it's much better than ablative. Just a different way of working. And don't forget, that while you can...
I also still have my original teak handrails on my 1974 T-22. They need a coat or two of oil or varnish , otherwise those "flimsy" teak rails are still...
I made my own teak hand rails a few years ago and it wasn't that bad. At the time I didn't have the better tools that I have now but managed to pull off a...
Hi Rob, I suspect the Metal Ready product you speak of is to prep the keel before applying POR 15. No such product is necessary prior to the Interlux products....
... I hope to finish grinding tomorrow, maybe next days off get the IP 2001 started. Suddenly the Spring is looking good, if I do go out West on course, I know...
To get the dirt and grime off, I simply use a wire brush fitted on my drill. It gives it a nice "polishing" or removal of oxidation, and it gets to the...
Next week is keel week. What about an electic chipper. Bruce PLEASE REPLY TO bruce@.... This message is being sent via BlackBerry on the Bell Mobility...
Just curious, why would they be taking them up if they aren't in your fleet. If they were trying to roll you they obviously were in the start after you. ...
Hi. I do not know about Robert or Dan but I purchased the Garelick #71090 which has 9.5 inches vertical travel.The original bracket (Spar) had approx 13 inches...
I love the thought of it, but maybe the hammer/scraper combo is where you should start, work our way up to power gear. It may come off easier than expected. ...
Michael, I can order carriage bolts from McMaster-Carr : They have 5/16" coarse thread SS lag bolts 3/4"-- 6" long with increment 1/4". 2-3 days delivery to...
Jakov Kogan
jakov.kogan@...
Apr 2, 2006 1:28 am
30167
Hello Tanzer sailors, After many years away from this board and the class I thought I'd put my name back up here for tips and tricks about making your Tanzer...
In a message dated 4/2/2006 6:21:11 A.M. Eastern Standard Time, tanzer@yahoogroups.com writes: I made my own teak hand rails a few years ago and it wasn't...
Yes, this is the only negative side to the Garelick bracket. I machined grooved an extra notch on the handle to increase travel. I forgot to tell you that I...
Thanks to all for the great feedback on this, as usual. ..and, yes, I was asking about the Blue for the `gunwale-stripe' and `boot stripe', not bottom-paint....
Rich Just to throw another drop in the old paint can mix: I did the upper stripe on Gypsy Rover http://personal.nbnet.nb.ca/rhall/r/Castine.jpg last summer ...
I am selling a 1982 Tanzer 22 CB (#2002). It has a 2001 trailer and a 10HP Honda - one set of sails. The boat urrently located in Hilton Head, SC. The asking...
