Hi Drew: Do you by any chance still own this Tanzer 16? I'm divided between this lighter boat and a Siren with a weighted keel. I'm a novice and my wife wants...
Wil To me, your key sentence is: "I'm a novice and my wife wants more comfort than speed." If you have a desire to own your own sailboat, to spend some quality...
I have noticed quite a few e-mails flying around concerning the replacement of light bulbs by LED's and am interested but would appreciate if this issue could...
Thanks everyone for the input on the foam vs butyl tape suggestions. Seeing as I've already ordered the foam and I've gotten some feedback that on the T-22's...
You will find that aluminum plate rubbing on the sheaves will corrode to dust, and mixed over the years with all that moisture will turn to a thick paste up...
Hey - I might be able to answer this one - I just did it YESTERDAY!!!!! My mast is down and after ... replace them or take them out and lubricate them ... ...
... No problems. They have polarity detection and voltage/current control built in (that's part of why they cost so much). Supposed to be good for 9 to 14...
... I haven't found one yet. Kent "Duct tape is like the Force. It has a light side and a dark side, and it holds the universe together." s.v. Luff Affair T26 ...
Kudos to Rik et al who take the time to take great pictures while working on their projects and paste the links into their e-mails (and/or the pictures/file...
I am about to embark on a project to replace the sheaves. Last year my main halyard was running very tight. A few years back I had the mast head off and noted...
... I was not able to remove the compression tube - hence - unless I cut out the aluminum sheeting, make a new piece and just fit it around the tube - I am...
Make sure you mark the position of each port frame as you remove it. The screw holes rarely align if you try to re-install a frame in a different opening. ...
Ahoy 1 - As best you can (and I often forget myself) - please change the Subject heading of the email if you change the subject of the text. It really helps to...
Rik and others. How about applying a little heat to masthead and knock it out. As for divider plate, it is simple a aluminum sheet...trace old and cut new....
Hello all....just wondering if anyone has the pin to pin measurement for the forestay for replacing the roller furling unit on a tanzer22....? Also, does...
Mulhern, Molly
molly_mulhern@...
May 1, 2006 4:20 pm
30803
Ok, per you and Rick, I will check again. If I can get the top off that would be great. Has anyone switched their halyards over to wire to rope splice...
For sale: One North sail + sail bag, good to very good condition: ~15 years young (not sure), two reef points, leech line etc. Asking $Cdn 400.00 + shipping....
I just finished replacing the sheaves on the masthead. It comes off by removing the single 1/2 inch bolt which goes right through the mast. (very easy). I...
... I went one season rope/wire splice, better than the thimble thing, then went all rope. It's really worth doing, I knew better and should have gone rope but...
I have built a few spacer plates over the last 2 years, one for me, and a few spares, most of which I have given away. I have one more left if anyone wants it,...
If this is the plate that separates the sheaves that I mentioned is all corroded and if I can get the top off my mast and it sounds like I need to remove a...
If this is the plate that separates the sheaves that I mentioned is all corroded and if I can get the top off my mast and it sounds like I need to remove a...
I am in Nova Scotia, and yes the compression post has to come out. Mine just slid out, if not a few taps and maybe some heat will help. It should be loose. I...
If this is the plate that separates the sheaves that I mentioned is all corroded and if I can get the top off my mast and it sounds like I need to remove a...
I had the same problem last year. I replaced the old style halyards with all rope. I ran them internally in the mast, I now have to sheaves instead of 4. Not...
Also, make sure you read this and/or are aware of this BeFore you randomly remove all your frames and throw them in one big pile. [Not that I would know...
In a message dated 5/1/2006 9:05:16 A.M. Eastern Standard Time, tanzer@yahoogroups.com writes: Do you by any chance still own this Tanzer 16? ... I've owned...
My boat is new to me last season and I have to apply Bottomkote XXX but can't remember how much the previous owner said it required. I think it is either 3 or...
