For sale, 2 volvo 164's #1- 1969 164 red, 4 speed, air conditioning, good engine, and transmission, really good parts car(rusty) #2- 1975 164E green,...
Mini1298
mini1298@...
Apr 5, 2002 1:54 am
837
Ok am I just being silly or can you use a ditributor from an injected 164 with the injection points rmoved in a carburetor 164. Or are the block hole and...
Att: David Hallarn Sure you can use the distrubuter from E engine on an A engine fits neatly. Rolf Ericson ... From: "David Hallam" <hallam@...> To:...
Just to let evryone know, the 1975 164 I have for sale also has been lowered about 2 inches, has front and rear ipd sway bars, and some new polyurethane...
Mini1298
mini1298@...
Apr 5, 2002 11:34 pm
841
Morning i'm just scanning a 1998 review of the 144 from a New Zealand mag - covers some history and they 'road-test' a '74 model. If anyone would like a copy ...
thanks for all your positive replies.where can i get those black stripe,tape like that goes just under the window.in the dealer parts section they are so...
Hi i'm interested. Can you contact me off the group. volvo162@... Steve ... transmission, really good parts car(rusty) ... miles)including overbore,...
Morning All Does anyone have any advice they could give me on options for replacement shocks for our '72 164E? Ours is getting a little soggy in the...
I'd recommend Bilsteins. Several years ago, I bought a set of KYB's that were supposed to fit and after several attempts, I gave up and called there sevice ...
DEN544@...
Apr 7, 2002 1:49 am
847
Hi Dale If i read you right, you're recommending a way to make an easy fifty bucks. Nice move, and extra thanks. bruce & lisa ... ...
... Bilsteins ... Rear springs probably suspect. Those in my '71 measured out at a whole 25 PSI on the tester! Install 240 upper mounts and then use 240 rear...
Hello! As this is my first summer with the car, I am wondering if there is anything special I need to do to "summerize" it. BTW- the temp & gas gauges are...
Lila: I'm not a bad person and I try to stay original to my car.... but a General Motors mulit-use wiper motors and bucket will work fine in your car. There...
... Hi DS Thanks for that - do you know if the 264 back end is the same - i.e. would they fit... and are they likely to be any stiffer than those for a 24? i...
Hi! Sorry 200 series rear shocks are a bit different at the lower fitting on the 100 series, can be modified by shortening the sleeve for lower bolt. 164E 1975...
... <snip> On my '73 145, I removed the stud assembly for the rear shocks on the trailing arm. Installed a pair of 240 rear shocks on it after doing that. ...
Dear Sirs, would you be so kind to UNSUBSCRIBE my e-mail-adress johannes.unterberger@... Thanks in advance! Yours sincerely, Johannes Unterberger...
Unterberger, Johannes
Johannes.Unterberger@...
Apr 10, 2002 8:14 am
856
Hi So... is there any consensus on what might constitute a 'dream' suspension for a 164? i'd really like to have mine handling as well as it can - with this...
Hi, I am wondering if any of you's know any good volvo pages/sites that cover all the different models from the beginning to some of the recent models. I used...
B: I've never used them, but I hear great things about the variable rate springs from Vperformance. I know they make a set for the 1800 and do a bunch of other...
... Here is attached a .jpg figure of round gauges for 140, but it is quite the same for 164. Jean-Pierre...
LE-LAGADEC Jean-Pierre
jean-pierre.le-lagade...
Apr 11, 2002 7:30 am
861
WOULD YOU BE SO KIND TO UNSUBSCRIBE johannes.unterberger@... Yours sincerely, Johanes Unterberger...
Unterberger, Johannes
Johannes.Unterberger@...
Apr 11, 2002 9:26 am
862
Hi all, I took my 164 into the shop to fix a rumble when accelerating and cornering left ( starts at about 45+ mph, goes away at about 65-70mph). They replaced...
... It sounds as if it is actually in one of the *right* wheel bearings. Remember, when you are cornering leftward, the RIGHT wheels go through a larger arc...
Try your engine mounts!!!!!!!!!!!!!!!! often missed. /dlh. ... -- David Hallam At home on Libranet 2.0 linux -- A Volvo, Daimler and BMW nut. "Without...
