The part mentioned at Agson is list $63.00 at HP's parts and is available. RG5-2651-090CN Also if checking many suppliers leave the -090CN off, easier to...
Is it hooked to a Dell??? If you let Dell computers self install the printer, 400's & 4050's will run at 4 PPM. Install new drivers from HP.com & all will bw...
Also, check the driver it's using. PCL6 drivers on WinXP default to 1200x1200 dpi which causes the printer to print very slowly (8ppm). You can install the...
Jim O'Connell
joconnell@...
Jul 12, 2007 5:19 pm
22682
my printer is Canon i6100 and now this printer is blinking. How to reset my printer ?...
Were you successful in printing an engine test with this machine??? ************************************** See what's free at http://www.aol.com. [Non-text...
Media path error. Has anyone seen this error. Xerox was pretty vague. It seems like it has something to do with printhead wipers. If I try to send eliminate...
Anyone else have any suggestions on this error? The last thing I just tried was to swap out the DC controller and this didn't help either. The only other thing...
While we are on the subject of duplexing I also have an HP8150 that will not duplex without jamming. I have tried several different combinations of fusers and...
I have an Hp8000 that keeps giving me a 55.a error whenever there is a duplexer installed. I have swapped out the duplexer several times as well as the fuser...
Yes it can be a power issue . . Try to isolate this printer on it's own or with low draw items. . Years ago I had a 5Si that was on the same circuit as the...
I always remember the 8000's we had at my last job had lots of issues with the power supply itself. I must have replaced tons of those b/c they constantly...
CAN ANYONE HELP. GOT A ERROR WHEN UNIT IS TURNED ON " E000" I HAVE REPEATED SWITCHING ON AND OFF ALSO REMOVING THE FORMATTER BOARD, BUT ERROR STILL PERSIST.....
Try changing the fuser unit. This is because the fuser output delivery roller is worn out, it can't hold the paper properly and delay feeding into the...
Derik, Get rid of the power strip. Plug the printer directly into the power outlet, all of the printers as well. HP suggests plugging the printers directly...
There were two different duplexers used with the 8000 - one that is bsckward compatible with 5SI - be careful - the only way to tell the difference is by the...
Try replacing the fuser and see if that helps. ... -- The Force is a lot like Duct tape. It has a light side, a dark side, and it holds the universe together. ...
I'm having an issue with my new Lexmark monochromatic laser printer. Printing toner at 100% black (text and image) works great but when I go to print a...
Have a 2500 that will not stop the cartridges in the right spot to remove, the guide pins do not align with the slots. It also will not always identify the...
Hi I have a canon pixma MP500. It was printing just fine and then the big black tank quit working. I got a new tank, but that didn't do anything, I emailed...
Hello, Experts I am having an issue with a HP2420, after the user replaced an expired toner now the printer will only print an image on 2/3 of the right side...
Hello, I have a Lemxark T620 and I need to print a bunch of labels with it. So I purchased a few 12A6360 cartridges. Which are supposed to be for printing...
HP 5500N, display showed two lines of "asterisks". Was told to replace Flash memory,(C9712-67922), when I did this, display went blank, put "old" flash memory...
Was working on a HP CLJ 5500 ,when I got to the call, was just "flashing" 2 rows of asterisks in the display. Was told it needed "Compact Flash Firmware",...
I'm geeting blank pages and errors 54.11,12,13,14. I'm inclined to replace the high voltage power supply but with these numerical errors, it mentions the color...
I'm not sure what you mean by a cartridge for printing labels. Do the labels print OK with the original cartridge? If not, it may be the labels. Also try...
I read you replaced the ink tank, but you may need to replace the printhead. I'm not familiar with this model. I can remember when I used to get Canon inkjets...
Have you tried to replace the formatter board? David ... ____________________________________________________________________________________ Be a better...
